Dry Type Power Transformador De 4mva 2500kVA 1000kVA 10kVA/6kVA/0.4kv Distribution Transformer Price

Product Description

Product Description

10kV and Below SC(B), SG(B) Series Dry-type Power Transformer
    
The epoxy resin cast dry type transformer of Special Transformer Company of Great is made with abroad advanced technology, it includes the following characteristics:

1.Low local discharge As the coil is cast in vacuum state, the air bubble produced in coil can be prevented effciently, the local discharging value fully accords with relative national standard.
2.Strong capability of lightning impact The lightning impact voltage that affects the insulation of transformer windings along the initial voltage distribution of windings, the foil type windings initial voltage distribution approaches to linear one, therefore, the transformer manufactured by us has good ability to resist the lightning impact.
3.Strong ability to resist short-circuit The width of copper foil of LV windings that is the reactance height, LV current is supplied according to be the requirement for ampere turns balance among windings, HV/LV windings axial force caused by short circuit tends to zero.
4.Good performance of anti-drying crack The transformer manufactured by us is made of packing type resin and designed into the structure of full copper oil, the coefficient of insulation material is the similar to the that of thermal expansion of copper conductor, so the coils can be prevented cracking efficiently. The transformer has been done kinds of anti-crack tests, such as cold/hot alternation test, thermal impact test, rapid aging test, etc, and the test result demonstrates that our technology can meet the requirements of service occasions like low temperature, high temperature and large range of variable temperature, as well as anti-crack after the transformer runs for a long time.
5.Strong over-load capability If the transformers of same capacity whose load consumption is equal, the sectional area of copper foil will be increased correspondingly, and the volume  will be extended with the sectional area that requires more packing resin, therefore, both the thermal capacitive property of windings and short-time over load capability of transformer are quite strong.
6.Good flame retardancy The transformer has visible features such as free-maintenance, moisture-proof, anti-damp and hot, flame-retardant, selfextinguishing, etc., besides, its stuffing type resin casting technology is good for environmental protection. When bum by the electric are at high temperature, it will not product any noxious gas. The superior flame retardancy is proved in the burning test. The product has good ability to adapt to environment, on the basis of European HD464 standard, it reaches the environment class E2, weather-resistant class FC2, flame-retardant class F1, it can be widely used in fields or locations where service conditions are rather atrocious such as commercial area, under ground, power plant, steamship, offshore drilling platform, etc.
7. Low noise Because of special structure and design, the noise produced by transformer is reduced greatly, compared with the noise value stipulated at national Specialized Standard, its whole noise level is lower than it for more than over 10-13dB(A).
8.Low consumption Compared with "8" character type products, SCB9 series has better economic benefit, its total consumption is reduced for 10~15% in average.

Detailed Photos

1. Iron core
    Made up of high quality cold rolled silicon steel sheet that is for electric engineering
2. Low voltage winding
    Made up of a whole copper foil coil
3. High voltage winding
    Made up of sectional type vacuum casting double glass-fiber covered coils
4. Low voltage terminal
 

5. High voltage terminal
    Variable wiring mode, which is convenient for installation
6. Resilient pad
    Avoid mechanical resonance, and reduce noise
7. Clamp and trolley
    The wheel of trolley can rotates to 90°
    It is convenient for vertical and horizontal movement.
8. Packing type resin insulation
    With advantages of damp proof, anti-damp and hot, flame-retardant, and selfextinguish.

 

Product Parameters

   

 

Certifications

 

 

 

Our Service

1.Quick response in before sales period help you got order

2.Excellent service in production time let you know each step we made

3.Reliable quality solve you aftersale headache

4.Long period quality waranty ensure you can buy without hesitate

Workshop

 

Packaging & Shipping

 

 

FAQ

 

1.Q: Are you manufacturer?
    A: Yes, we are manufacturer.
2.Q: Can I get guarantee of products?
    A: Yes, each product is 1 year quality warrantee under customer correct using the products.
3.Q: How to buy it? What about the delivery?
    A: Please contact me by email or online, let me know your requirement, we will provide you professional solution. We have shipping agent can choosing the cheapest and fastest delivery. FOB,CIF, C&F, FCA or EXW, each is available to us
4.Q: How can I pay you?
    A: T/T and L/C
5.Q: What about the production?
    A: Produce time is 2~4weeks.
 6.Q: Could you offer some spare parts?
    A: Yes, no problem.